DL1SP13FR Chrome Duallyvalve Kit W/ Front Stems
Front Stems: Qty: 2
Because of the small diameter of the hole and the placement of the wheel cover you may need to cut a notch for accessibility in the cover. Or take the cover off. You have 2 Front stem options below, please specify which you would like. Please indicate in the order notes.
VHVS8175 Valve Stem Reverse Mount 1 3/4 With a 10-15 deg bend (NO COVERS BEING USED)
VHVS8225 Valve Stem Reverse Mount 2 1/4 With a 20 deg bend (COVERS BEING USED)
NOTE: IF YOU ARE USING "AFTERMARKET SIMULATORS", YOU MAY NEED A 2.75" FRONT WITH A 20 DEG BEND. PLEASE MAKE A NOTE OF IT IN THE ORDER NOTES, OR CALL. 818-352-8717 X111 - KELLI
SUGGESTED WHEEL COVER REMOVAL:
<< This picture shows VHVS8225 2.25" Straight stem and an OEM Simulator.
Wheel Size: 16in.
Inner / Outer Wheel Types: Steel / Steel
Stabilizer Shape: Round
Hand Hole Size: 1-1/2in.
MAKE & MODEL: Sprinter
(2) INNER DUAL WHEEL CHROME VALVE STEMS
(2) OUTER DUAL WHEEL CHROME VALVE STEMS
(2) STABILIZERS (Go in the outer Wheel that stabilize the inner dual wheel stem. Does not go in the cover / simulator cover)
(1) PACKET OF LOCTITE (For Reverse Mount Stems)
(2) FRONT WHEEL CHROME STEMS VHVS8175B15 or VHVS8225B20
The Duallyvalve kit makes it easier for Motorhome or Commercial Vehicles to check and maintain tire pressure on six-wheeled chassie. Traditionally adding air to dually tires was difficult, and required the use of specially designed air chucks and specially designed air gauges just to get to the valve stem. Not anymore! The length of the inner dual valve has been extended to reach the outer dual thus making it easy to add air.
Any Cracks or leaks, we will cover the cost of repair or replace them 100% of the time.
IMPORTANT RE: SIMULATOR COVERS: The OEM Simulators are "Clip-on" not "Bolt-on" So they can rotate and cut a gouge in the Duallyvalve stems and or just fly off. We recommend to wire tie or zip tie your covers to your wheel in a few positions to prevent this.
Metal Zip Ties on Front Wheel:
What the cover can do to the valve stem:
BALANCING: If you plan on using balancing compounds in your tires such as Equal or Counteract; please indicate that information in your order notes.
TPMS: All of our valve stems in the Dually valve kit can accommodate TPMS Sensor Caps, that go on the end of the valve stem.
Note: To reduce potential future air leaks; we recommend after 5 years replacing the rubber seals on the valve stems in the Dually Valve Kit. Just give us a call and we would be happy to help you get what you need.
Replacement Grommets needed for your kit are...
(4) VHRG80B Black Rubber Grommet .453 (Use Alone, Lip on both sides)
(4) VH515RG Rubber Grommet .453 (Use with VH515FW)
(4) VH515FW Flat Rubber washer .453 (Use with VH515RG)
If you would like to replace your stabilizers also the part # is...
(1 per outer wheel)
Stabilizers Part #: VHRG15 Round 1.5"
We also reccomend to wire tie or zip tie the wheel covers to the wheel in this application. They tend to rotate and fly off.
Inner Stems will have to be bent in order to be centered in the outer hand-hole - please refer to the following bending Instructions
Installation Instructions - Bolt In Valve Stems
Stack the Duals
Check if the inner stem is centered in the hand-hole
Bend the valve stem slightly, so the stem is centered in the hand-hole. (When bending support support the base and keep the valve cap on to protects the threads).
Re-stack the duals to confirm that the valve stems are centered
Please see File Tab for further information
Attention: Please refer to Duallyvalve Application Sheet updated August 2015